不同进水流速对泵站进水池漩涡的影响

为探究泵站进水流速大小与泵站进水池水流流态、漩涡的产生与发展变化规律,结合泵站实际运行情况,建立引渠、前池、进水池和进水管的泵站物理模型和湍流数学模型,采用VOF模型和非定常的SST k-ω湍流模型对9种不同流速的泵站进水水流特性进行数值模拟,分析不同进水流速的泵站进水池水流流场分布、漩涡涡量的变化及分布规律。研究结果表明:当进水流速为0.322 2～0.564 2 m/s时,泵站表面漩涡的强度随进水流速的增大而增强:当进水流速为0.322 2～0.401 6 m/s时,进水池出现Ⅲ、Ⅳ型漩涡;当进水流速为0.483 5 m/s时,进水池出现Ⅴ型漩涡;当进水流速为0.520 8～0.564 2 m/s时,进水池出现Ⅵ型漩涡。将数值计算结果与模型试验结果进行对比,两者基本吻合。研究结果可为泵站工程设计提供参考。     

注射模生产中智能化控制及应用

分析了注射模生产的现状，针对其生产中智能化调控应用方面的不足，提出模内参数的自适应调节方案，还介绍了自适应工作的原理、可调参数种类、逻辑推理等，并实际验证了基于注塑设备联网集成工艺数据下注射模成型工艺自适应调节的可行性。     

Life cycle assessment of HFC-134a production by calcium carbide acetylene route in China

HFC-134a is a widely used environment-friendly refrigerant. At present, China is the largest producer of HFC-134a in the world. The production of HFC-134a in China mainly adopts the calcium carbide acetylene route. However, the production route has high resource and energy consumption and large waste emission, and few of the studies addressed on the environmental performance of its production process. This study quantified the environmental performance of HFC-134a production by calcium carbide route via carrying out a life cycle assessment (LCA) using the CML 2001 method. And uncertainty analysis by Monte-Carlo simulation was also carried out. The results showed that electricity had the most impact on the environment, followed by steam, hydrogen fluoride and chlorine, and the impact of direct CO₂ emissions in calcium carbide production stage on the global warming effect also could not be ignored. Therefore, the clean energy (e.g., wind, solar, biomass, and natural gas) was used to replace coal-based electricity and coal-fired steam in this study, showing considerable environmental benefits. At the same time, the use of advanced production technologies could also improve environmental benefits, and the environmental impact of the global warming category could be reduced by 4.1% via using CO₂ capture and purification technology. The Chinese database of HFC-134a production established in this study provides convenience for the relevant study of scholars. For the production of HFC-134a, this study helps to better identify the specific environmental hotspots and proposes useful ways to improve the environmental benefits.     

寄居于非旁轴矢量光束的李萨如线的相互作用

从理论和数值模拟两方面研究了寄居于非旁轴矢量光束的两条李萨如线的相互作用。研究发现：李萨如线因不稳定而在传输中消失，并有李萨如奇点出现。当传输距离、振幅因子、离轴距离和光束波长变化时，李萨如奇点的位置，偏振度和李萨如图形可能发生改变，还会发生成对李萨如奇点因带有相反拓扑电荷而接近和湮灭。研究结果对深入理解非旁轴多色矢量光束奇点光学和寻找奇点光学潜在应用具有一定参考价值。     

稳产国Ⅵ柴油并兼产喷气燃料技术方案的工业应用

介绍了浙江石油化工有限公司新建的3 Mt/a柴油加氢精制装置，其配套使用中国石化石油化工科学研究院有限公司开发的催化剂级配技术，并实施了可根据原料供应及市场产品需求情况灵活调整切换的2种生产技术方案。1 a的安稳生产运行结果表明:该装置以直馏柴油为主原料，通过分馏塔的馏分切割及其侧线抽出，实现了稳产国Ⅵ柴油并兼产喷气燃料技术方案的工业化应用；在实施以兼产喷气燃料为主的生产技术方案时，通过调整常一线柴油的掺炼量，不仅可以生产含硫量小于10.0 μg/g的精制柴油产品，同时兼产所得到的喷气燃料产品含硫量小于0.5 μg/g，赛波特颜色号值大于30；在实施主产精制柴油组分方案时，通过掺炼质量分数为20%~40%的催化柴油，并使所提炼得到的精制柴油组分含硫量小于6.0 μg/g的前提下，这些精制柴油组分产品既可直接作为满足国Ⅵ柴油产品出厂待售，也可作为柴油调和组分储存待用于产品的进一步优化。     

高含盐工业废水处理技术研究进展

现代工业生产的工业废水往往含有超量的有机危害物或过量的盐、酸碱等,在对此类废水进行处理时,传统的方法将无法起到有效的作用。且由于此类废水同样不适宜微生物的生长,利用微生物进行污水处理的方式也受到很大的局限。对于这种工业排污废水,在实现有机物的降解之外,还需要实现无机盐和废水的分离来达到排污标准。对现在针对高含盐废水的成熟处理技术进行了总结,介绍了几种常见处理技术的特点及应用,以及他们在实际高盐工业废水处理中的作用和一些问题。通过对现有高盐废水的处理技术的分析和了解,可以针对不同类型的高盐废水使用不同的处理方式以达到最大的经济效应,并且对实现排放量最小化具有重要意义。     

锌铝水滑石的制备及其在制革少铬鞣中的应用

通过共沉淀法制备了锌铝水滑石(ZnAl-LDH),采用XRD、FTIR、SEM对其结构进行了表征.将其配合用量为皮质量2％的铬粉(记为2％铬粉)应用于制革鞣制工艺中.考察了ZnAl-LDH制备时的金属源物质的量比、陈化时间对鞣制坯革收缩温度、鞣后废液中的Cr2O3质量浓度的影响.结果表明,ZnAl-LDH是尺寸在100～400 nm之间的片状材料.当n〔(Zn(NO3)2?6H2O)〕:n〔Al(NO3)3?9H2O〕=2.0:1.0,陈化时间为6 h时,制备的ZnAl-LDH-4具有优异的性能.与单独使用2％铬粉鞣制坯革相比,ZnAl-LDH-4(用量为皮质量的4％)配合2％铬粉鞣制坯革收缩温度由75℃提高到94℃,废液中的Cr2O3质量浓度由99.58 mg/L降低至46.98 mg/L,且加入ZnAl-LDH-4鞣制后,鞣后废液化学需氧量和生物需氧量均降低.     

Influence of fluorine-containing side chain on the properties of waterborne polyurethane-urea

In order to prepare waterborne polyurethane with excellent water resistance and thermodynamic properties, a series of side chain fluorinated waterborne polyurethane-urea (FWPU-UA) was synthesized with polytetramethylene ether glycol, N-(2-methyl-1,3-propanediol-2′-)-perfluoro-1-butanesulfonyl amine (NPBA), isophorone diisocyanate, and isophoronediamine. With the increase of NPBA content, the weight loss temperature, glass transition temperature, and tensile strength of FWPU-UA were all improved. Gaussian fitting analysis of infrared data and density functional theory simulation proved that the introduction of fluorine side chains increased the interaction of hydrogen bonding in the FWPU-UA. X-ray photoelectron spectroscopy analysis indicated that the aggregation of fluorine atoms on the surface of film were caused by the migration and enrichment of fluorine side chains. Furthermore, the water resistance of polyurethane-urea film could be significantly improved by adding a small amount of NPBA, and the seven-day water absorption rate of polyurethane-urea film was reduced from 30.13% to 12.55%.     

Chromium-promoted preparation of forsterite refractory materials from ferronickel slag by microwave sintering

The chromium-promoted preparation of forsterite refractory materials from ferronickel slag was investigated by microwave sintering of the slag with the additions of sintered magnesia and 0–10 wt% chromium oxide (Cr₂O₃). The thermodynamic calculations revealed that the addition of Cr₂O₃ can promote the formations of spinel and liquid phase and maintain high content of forsterite below 1500 °C. The experimental results showed that there existed a stronger promoting effect of Cr₂O₃ additive on the properties of refractory materials in the microwave field than that in conventional sintering. It was attributed to the preferential formation and growth of spinel with stronger microwave absorption than other phases (e.g., enstatite), the existence of more forsterite, and the enhanced densification in association with the presence of more liquid phase at the same temperature. By microwave sintering of the mixture of ferronickel slag, 25 wt% sintered magnesia, and 4 wt% Cr₂O₃ at 1350 °C for 20 min, a superior refractory material with refractoriness of 1801 °C, thermal shock resistance of 6 times, bulk density of 2.97 g/cm³, apparent porosity of 1.4%, and compressive strength of 197 MPa was obtained. Compared with that prepared by conventional sintering at 1350 °C for 2 h, the refractoriness and thermal shock resistance were increased by 175 °C and 100%, respectively. The present study provided a novel method for preparing high-quality refractory materials from ferronickel slag and relevant industrial wastes.